Invitation card

Jessica · Post by **Jessica** » May 21st, 2008, 11:08 am

i have a problem on how to solve this: http://sallander.com/origami_jessica.jpg

It is an invitation card and as you can see you open the card by pulling two edges apart. Sweet and simple! I don't know if you can help me, but if you have seen this or something similar somewhere before ( a diagram) or any book recommendation...or if you know where I could get some help it would be lovely!

Thanks!!
Jessica

Ondrej.Cibulka · Post by **Ondrej.Cibulka** » May 21st, 2008, 1:08 pm

Welcome to the forum! I will wait if someone know it and then I try to make it in the tram during my way home...

fi-ori · Post by **fi-ori** » May 21st, 2008, 1:49 pm

I have seen similar models on the Tomoko Fuse's book "Home decoration with origami": card 1 or card 2, pg 32-35.

Jessica · Post by **Jessica** » May 21st, 2008, 4:09 pm

Thank you Ondrej! If you could have a look it would be great!

About the book, I started looking for it but it seems to be quite old and therefore difficult to get hold off. And unfortunately google books did not seem to have it. Does anyone have the book so that you could scan/take photos of these pages and send it to me by email (origami "at" sallander "dot" com)?

Thank you all in advance!

Jessica

Ondrej.Cibulka · Post by **Ondrej.Cibulka** » May 21st, 2008, 6:00 pm

It looks like simple twist:

[img]http://i58.photobucket.com/albums/g275/ ... essica.jpg[/img]

Use your own ratio, I suggest that it is not folded at half. Please, send me, if is it what you mean.

Jessica · Post by **Jessica** » May 21st, 2008, 7:03 pm

Thanks for the instructions! I get as far as to the last step but don't understand how to continue with the following corners.. and to the final result?

Thanks again!
Jessica

Ondrej.Cibulka · Post by **Ondrej.Cibulka** » May 22nd, 2008, 2:47 pm

I was hurry, so maybe it is not so clear. It is just twist. I will make short video (my card in the camera is 32 MB, so I cannot make long video) and post it here (tomorrow).

Jessica · Post by **Jessica** » May 22nd, 2008, 3:00 pm

Thank you! I look forward to the video tomorrow!
Jessica

mrsriggins · Post by **mrsriggins** » May 22nd, 2008, 10:02 pm

Here is the model at the last step.

Fold the flap down (valley fold)

After flap has been folded down. Turn the model around and fold the back flap down also.

In the process of folding the back flap down.

Both flaps folded down. Now open the model up from the middle.

Looks like this. Now turn the model over....

and Voila! To open grab two diagonal squares and pull. To close grab two diagonal squares and push.

Ondrej.Cibulka · Post by **Ondrej.Cibulka** » May 23rd, 2008, 10:24 am

EDIT: You probably need to Quick Time player to see the video, I am not sure:
http://www.apple.com/quicktime/download/

And video. I have only 30 sec to show everything, so it is probably to fast to understand. Of course, my model collapsed alone, because I have pre-creased paper:

Jessica · Post by **Jessica** » May 23rd, 2008, 2:02 pm

Thank you all very much!!! Now I just have to figure out at what ratio it has been made (or the parts "sticking" out) which probably is more difficult than it seems

.

Thanks again!
Jessica

xaoslord · Post by **xaoslord** » May 23rd, 2008, 10:25 pm

Here is what I came up with. (Sorry about the quality, but I'm having to make due with what I have at work.)

To get here, I started with step 3 of Ondrej's diagram. To get the vertical crease, I folded the edge to the center, creasing only at the top edge(point 1). I then folded the edge to the pinch mark I just made and creased only the top(point 2). I then folded those pinch marks together (point 3), and finally that pinch mark with the first one (point 4.) I did the same with the horizontal crease, only starting with a fold at the halfway point (Point 1):

Once again, I apologize for the quality. I had to use MS Excel and MS Paint for this. The only camera I had was my cell phone.

Jessica · Post by **Jessica** » May 24th, 2008, 10:16 am

Great!! Now I've got it!
Thank you all for a fantastic forum!

Jessica

fi-ori · Post by **fi-ori** » May 24th, 2008, 5:35 pm

nice twist

maybe using the first vertical crease as reference the other pinches can be spared